Overvoltage (12v) in Upboard - How to recover data
Hi,
I, unfortunately, overvoltaged the board with 12v. I was able to boot a couple of times but now the screen appears completely black all the time when I power it. I noticed that when I booted the consumption was 2Amps and now it just consumes 1 amp.
I found two questions about the same topic https://forum.up-community.org/discussion/2069/now-that-i-fried-my-only-up-board , https://forum.up-community.org/discussion/comment/8806#Comment_8806 and it seems that there is not any possibility to recover the board.
I am trying to read how to (somehow) recover the information in the eMMC. is it possible? I hope there is a way of entering to some recovery mode with minimal usage to read the eMMC content.
Any advice will be appreciated.
EDIT: I am trying to move the post to the right forum but I cannot, I am referring to this version of UpBoard https://www.mouser.es/ProductDetail/AAEON-UP/UP-CHT01-A22-0432-A11?qs=XeJtXLiO41S0JpGxYUwwTg==&vip=1&gclid=Cj0KCQjwpfHzBRCiARIsAHHzyZp5Xa62d5NyrGmaaJTqPYxNenGVujjHTFcOzXlk02nNI2dJcbBT8uQaAuaZEALw_wcB
Comments
-
Hi @pramon
I am afraid that, if you have given that much voltage, you have severely damaged the board and you won't be able to recove/use the board normally.
The only way would be to de-solder the eMMC and re-solder on another UP Board, but you would need to specific equipment to do that.
-
@pramon said:
Hi,I, unfortunately, overvoltaged the board with 12v. I was able to boot a couple of times but now the screen appears completely black all the time when I power it. I noticed that when I booted the consumption was 2Amps and now it just consumes 1 amp.
I found two questions about the same topic https://forum.up-community.org/discussion/2069/now-that-i-fried-my-only-up-board , https://forum.up-community.org/discussion/comment/8806#Comment_8806 and it seems that there is not any possibility to recover the board.
I am trying to read how to (somehow) recover the information in the eMMC. is it possible? I hope there is a way of entering to some recovery mode with minimal usage to read the eMMC content.
Any advice will be appreciated.
EDIT: I am trying to move the post to the right forum but I cannot, I am referring to this version of UpBoard https://www.mouser.es/ProductDetail/AAEON-UP/UP-CHT01-A22-0432-A11?qs=XeJtXLiO41S0JpGxYUwwTg==&vip=1&gclid=Cj0KCQjwpfHzBRCiARIsAHHzyZp5Xa62d5NyrGmaaJTqPYxNenGVujjHTFcOzXlk02nNI2dJcbBT8uQaAuaZEALw_wcB hydrogenexecutor.app
Unfortunately, recovering data from an UpBoard fried by overvoltage can be incredibly challenging, bordering on impossible in most cases.
Categories
- All Categories
- 63 Announcements & News
- 139 Product News - New Product/Product Change Notice/ End-of-life
- 112 Welcome Developers!
- 60 Unboxing & Project Sharing
- 114 Tech Updates
- 3.6K UP Products
- 119 UP 7000
- 25 UP Squared i12
- 24 UP Xtreme i12
- 14 UP Squared Pro 7000
- 1 UP Element i12 Edge
- 24 UP Squared V2
- 65 UP 4000
- 23 UP Xtreme i11
- 34 UP Squared 6000
- 59 UP Squared Pro
- 135 UP Xtreme
- 820 UP Squared
- 1.4K UP Board
- 74 UP Core Plus
- 217 UP Core
- 3 UP Xtreme Lite
- 40 UP AI Edge
- 265 Starter Kits & Peripheral