UP 4000 Hardware Specification — upcommunity https://forum.up-community.org/ Sun, 16 Aug 2026 15:56:08 +0000 en UP 4000 Hardware Specification — upcommunity INTEL AX210 WI-FI MODULE CONNECTIONS https://forum.up-community.org/discussion/35162/intel-ax210-wi-fi-module-connections Sat, 10 Jan 2026 16:05:36 +0000 UP 4000 Hardware Specification Milasota 35162@/discussions Hi

I need the following information about the UP4000:
1) What type of interface does the Wi-Fi module (INTEL-AX210) mounted on the "carrier board for Wi-Fi and 5G" use? Is it the PCIE bus,the SMBus or the USB 2.0 port?
2) Is it possible to obtain the wiring diagram for the Wi-Fi module (INTEL-AX210) on the CN21 (high-speed expend connector)?
3) How do pins 29 and 30 of the CN21 (high-speed expend connector) work?

Best regards

]]> UP 4000 - USB PORT https://forum.up-community.org/discussion/35111/up-4000-usb-port Wed, 10 Sep 2025 14:22:29 +0000 UP 4000 Hardware Specification Milasota 35111@/discussions Hi

I'm trying to replace the EOL UP board with the UP 4000 board.
I've previously used the following USB 2.0 ports:
P0 on CN40
P2 on CN7
P3 on CN7

Can I found the same USB 2.0 ports on UP 4000 BOARD ?

UP 4000 description lists 2 USB 2.0 ports only but in data sheet I found
DP0/DN0 CN4
DP1/DN1 CN4
DP/DN_P1 CN5
DP/DN CN21
DP/DN_P6 CN15
DP/DN_P7 CN15

Best regards

]]> How to supply DC Power https://forum.up-community.org/discussion/35068/how-to-supply-dc-power Thu, 15 May 2025 22:50:12 +0000 UP 4000 Hardware Specification scottdg 35068@/discussions I would like to hardwire my UP to a lithium power supply. What is the correct power supply and any chance there is a diagram showing which leads to solder too?

]]> UP 4000 lower heatsink? https://forum.up-community.org/discussion/5303/up-4000-lower-heatsink Tue, 31 Oct 2023 21:46:20 +0000 UP 4000 Hardware Specification markvdb 5303@/discussions Hello,

I'm looking for an UP 4000 board to fit the Gainta G17081UBK 1U case - specs .

Looking at https://newdata.aaeon.com.tw/DOWNLOAD/2014 datasheet/Boards/UP 4000.pdf ,

  • The UP-APL03C2F-A10-0216 does not fit because of height restrictions.

  • The UP-APL03C2FLH-A10-0216 should probably fit. Can you confirm this?

I can easily find the UP-APL03C2F-A10-0216 in stock at European several distributors, but not the UP-APL03C2FLH-A10-0216 .

I've also found a comment that I do not fully understand. Does the UP-APL03C2F-A10-0216 kit contain all parts to convert it into the UP-APL03C2FLH-A10-0216? If not, is there anything else I can buy? Please advise.

Looking forward to a quick and efficient reply!

Kind regards,

Mark

]]> Working voltage range https://forum.up-community.org/discussion/5166/working-voltage-range Fri, 12 May 2023 12:48:17 +0000 UP 4000 Hardware Specification 3cells 5166@/discussions Whilst the input is specified at 12V what is the working voltage range, i.e. how high and how low an input voltage can the board safely tolerate?

]]> CN15 Connector for UP 4000 https://forum.up-community.org/discussion/5129/cn15-connector-for-up-4000 Fri, 10 Mar 2023 18:15:46 +0000 UP 4000 Hardware Specification tstaros 5129@/discussions I'm looking for connector manufacturer and part number for connector CN15, (USB/UART)?

]]> UP-4000 CN21 High Speed Expend Connector https://forum.up-community.org/discussion/5174/up-4000-cn21-high-speed-expend-connector Mon, 22 May 2023 05:04:13 +0000 UP 4000 Hardware Specification PHD 5174@/discussions Can you provide part no. for the 41pin fpc connector?

]]> UP-4000 CN19 Power Specs https://forum.up-community.org/discussion/5173/up-4000-cn19-power-specs Mon, 22 May 2023 04:28:25 +0000 UP 4000 Hardware Specification PHD 5173@/discussions Are the power specs for CN19 fan connector available - current?

]]> UP 4000 Heatsink Screws https://forum.up-community.org/discussion/5168/up-4000-heatsink-screws Sat, 13 May 2023 23:16:36 +0000 UP 4000 Hardware Specification scottdg 5168@/discussions What are the screw dimensions that holds the heatsink to the board?

]]> 40pin - Pin mapping in mraa changed ? https://forum.up-community.org/discussion/5163/40pin-pin-mapping-in-mraa-changed Thu, 11 May 2023 18:18:01 +0000 UP 4000 Hardware Specification Lubo 5163@/discussions I used UPBoard/ubuilinux/c/mraa until now. The pin mapping was clear for me.
It was like this :
mraa-gpio list
03 I2C_SDA: GPIO I2C
05 I2C_SCL: GPIO I2C
07 ADC0: GPIO AIO
08 UART_TX: GPIO UART
10 UART_RX: GPIO UART
11 UART_RTS: GPIO UART
12 I2S_CLK: GPIO
13 GPIO27: GPIO
15 GPIO22: GPIO I2C
16 GPIO23: GPIO
18 GPIO24: GPIO
19 SPI_MOSI: GPIO SPI
21 SPI_MISO: GPIO SPI
22 GPIO25: GPIO
23 SPI_CLK: GPIO SPI
24 SPI_CS0: GPIO SPI
26 SPI_CS1: GPIO SPI
27 ID_SD: GPIO I2C
28 ID_SC: GPIO I2C
29 GPIO5: GPIO
31 GPIO6: GPIO
32 PWM0: GPIO PWM
33 PWM1: GPIO PWM
35 I2S_FRM: GPIO
36 UART_CTS: GPIO UART
37 GPIO26: GPIO
38 I2S_DIN: GPIO
40 I2S_DOUT: GPIO

and I used pin 32 in my sw - initialized with MRAA_EnableIO( .... , 32) function.

But now I switched to UP4000 and there is something different. I am not able to initialize hw pin 32 (GPIO12) any more.

The MRAA_EnableIO( .... , 32) function returns me error :

Error exporting pin 32!

List of pins from mraa on UP4000/Ubuntu/pinctrl-upboard is like this:
mraa-gpio list
00 ID_SD: GPIO I2C
01 ID_SC: GPIO I2C
02 I2C_SDA: GPIO I2C
03 I2C_SCL: GPIO I2C
04 ADC0: GPIO AIO
05 GPIO5: GPIO
06 GPIO6: GPIO
07 SPI_CS1: GPIO SPI
08 SPI_CS0: GPIO SPI
09 SPI_MISO: GPIO SPI
10 SPI_MOSI: GPIO SPI
11 SPI_CLK: GPIO SPI
12 PWM0: GPIO PWM
13 PWM1: GPIO PWM
14 UART_TX: GPIO UART
15 UART_RX: GPIO UART
16 UART_CTS: GPIO UART
17 UART_RTS: GPIO UART
18 I2S_CLK: GPIO
19 I2S_FRM: GPIO
20 I2S_DIN: GPIO
21 I2S_DOUT: GPIO
22 GPIO22: GPIO I2C
23 GPIO23: GPIO
24 GPIO24: GPIO
25 GPIO25: GPIO
26 GPIO26: GPIO
27 GPIO27: GPIO

So I am confused... should I remap all may pins to different numbers ? I assume that I should use
MRAA_EnableIO( .... , 12) instead of UPBoard MRAA_EnableIO( .... , 32) ?
Or different issue is there ?

]]> Where is the schematic and pin specific functionalities for up 4000 board? https://forum.up-community.org/discussion/5140/where-is-the-schematic-and-pin-specific-functionalities-for-up-4000-board Thu, 30 Mar 2023 18:38:48 +0000 UP 4000 Hardware Specification susWorld 5140@/discussions Hi,
I am trying to write a driver for up4000 board and I need a datasheet that specifies how all pins are connected (schematic) and functionalities that each pin supports. I couldn't find all these detailed information in the "Datasheet" that is available on the up board website.
Can someone help me with this?

]]> Fan https://forum.up-community.org/discussion/5142/fan Thu, 06 Apr 2023 14:50:25 +0000 UP 4000 Hardware Specification scottdg 5142@/discussions I see the 2 pin wafer for Fan (12V) so I am hoping this will allow a thermal fan can be integrated? Thanks!

If yes, do you sell one?

]]> Screw Holes https://forum.up-community.org/discussion/5141/screw-holes Wed, 05 Apr 2023 01:04:38 +0000 UP 4000 Hardware Specification scottdg 5141@/discussions What are the distances between the holes?

]]> Is there a case available for the Up 4000? https://forum.up-community.org/discussion/5066/is-there-a-case-available-for-the-up-4000 Sun, 18 Dec 2022 10:27:12 +0000 UP 4000 Hardware Specification Markjlane 5066@/discussions Are there any cases available that may support the Up 4000 + m.2 expansion module?

]]> Cables & Connectors for UP 4000? https://forum.up-community.org/discussion/5091/cables-connectors-for-up-4000 Fri, 20 Jan 2023 19:15:14 +0000 UP 4000 Hardware Specification km6slf 5091@/discussions Page 49 of the UP 4000 (UP-APL03) Manual 2nd Ed.pdf lists details on the connectors and cables for UP 4000, but many of them don't come up when searched in the UP shop. I'm specifically looking for details for 170X000543, CN18, (Power / Reset button) and CN19 (Fan). I can make my own cables if the connector manufacturer and part numbers can be provided. Do any of you know the manufacturer and part number for CN18 and CN19?

]]> UP4000 : is there hw watchodg ? https://forum.up-community.org/discussion/5071/up4000-is-there-hw-watchodg Thu, 29 Dec 2022 10:07:29 +0000 UP 4000 Hardware Specification Lubo 5071@/discussions I have simple question, is there any hw watchdog implemented in UP4000 board ?

]]>